CellPowerX’s highest-output device
Flow rate is the number everyone quotes. What matters just as much is what you're actually breathing — so CellPowerX designed AirPlus around the water and the cell first, and let the 600 ml/min follow from that.
Where the difference is built in
Six choices behind the performance
Water polished first
Every batch is taken to 18 MΩ·cm resistivity before a single volt is applied — the ultra-pure starting point cheaper units go without.
Genuine high flow
A serious output platform: 600 ml/min of hydrogen alongside 300 ml/min of oxygen, in the 2:1 balance electrolysis produces on its own.
Sensors on watch
On-board electronics read water quality, temperature and level as you go, holding production steady and stepping in before anything drifts.
Two sealed chambers
Hydrogen and oxygen form in physically separate compartments with their own outlets, so the gas you inhale is never cross-mixed inside the cell.
Your choice of stream
Run concentrated hydrogen on its own, or blend in oxygen through the Y-connector — the device adapts to the session you're after.
Steady to the end
Managed cell temperature means the last minute of a six-hour run performs like the first, session after session.
The part that happens first
It starts with the water, not the current
Electrolysis is only as clean as what you feed it. Before AirPlus splits a single molecule, incoming water runs through an ultra-purification stage that pulls out dissolved ions, trace metals and contaminants, reaching resistivity of up to 18 MΩ·cm. Cleaner input, steadier and purer hydrogen — from your first breath to your last.

Two modes, one device
Choose how you breathe
Primary mode
Pure H₂ Mode
Send the full 600 ml/min of 99.99% hydrogen straight through the dedicated outlet — a concentrated, single-gas session with nothing else in the stream.
Secondary mode
H₂ / O₂ Synergy Mode
Bridge both outlets with the supplied Y-connector to breathe 600 ml/min hydrogen and 300 ml/min oxygen together, in the 2:1 balance they're generated at.
Technical specifications
| H₂ production | 600 ml/min |
|---|---|
| O₂ production | 300 ml/min |
| H₂ purity | 99.99% |
| H₂ / O₂ ratio | 2:1 natural electrolysis ratio |
| Water conditioning | Ultra-pure — water up to 18 MΩ·cm |
| Inhalation modes | Pure H₂ · H₂/O₂ Synergy |
| Session time | 30–360 min, 30-min steps |
| Operating voltage | 100–240 V ±15%, 50–60 Hz |
|---|---|
| Input power | 170 W |
| Tank volume | 2 L |
| Dimensions (W×D×H) | 197 × 197 × 321 mm |
| Net weight | 7 kg / 15.4 lb |
| Warranty | 2 years |
What's in the box
- ✓ 1× AirPlus device
- ✓ 2× Nasal cannula
- ✓ 2× Y-connector
- ✓ 1× Power cable
- ✓ 2× Fuse
- ✓ 1× User manual
Frequently asked questions
What exactly does a hydrogen inhalation device do?
It splits purified water into molecular hydrogen (H₂), which you breathe in through a soft nasal cannula. AirPlus is tuned for high flow and high purity, so even long sessions stay comfortable and consistent.
What's the output and purity?
600 ml/min at 99.99% purity — roughly twice what a typical portable unit manages. The built-in purification stage keeps that figure steady rather than letting it slide over time.
How do the two breathing modes differ?
Pure H₂ mode gives you a single 600 ml/min hydrogen stream. Synergy mode adds 300 ml/min of oxygen through the Y-connector, so you breathe both gases in a 2:1 ratio.
How long can one session last?
Anywhere from 30 to 360 minutes, set in half-hour increments. The 2-litre reservoir and thermal management are sized to keep output flat for the entire run.
Why does the water quality matter?
Impure water lowers efficiency, wears the cell faster and degrades the gas you breathe. Beginning with laboratory-grade water — up to 18 MΩ·cm — protects both the hardware and the purity of every session.
Ready to bring AirPlus home?
Ask us about pricing, availability and getting set up with your AirPlus Hydrogen Respiration System.
Buy Now

